Q: 
 A: 

What kind of lumber works best with Bull Brackets? 
Dimensional 2x4 and 2x6 lumber is required. For best results the lumber should be reasonably dry, particularly the cross beams. Kiln dried lumber, other than cedar, works best.
  

 Q :


 A :

At your display at one of the woodworking shows, your demonstration mentioned something about cutting the legs at a 15-degree angle.  Is that necessary ?
It is not essential.  Cutting the bottom of the legs at such an angle simply helps to provide a level sawhorse on hard surfaces.
 

What material do you use to make the brackets ?
Bull Brackets are manufactured from aluminum, .100” thick (100/1000’s inch).
 

 Q :
 A :

How much weight will a Bull Brackets sawhorse carry ?
It depends on the quality of lumber used. Simply put, it is as strong as the wood from which it is built. Care and common sense dictate that you do not overload any sawhorse to the breaking point.
 

Can I build a scaffold with this sawhorse ?
No! W.C.B., O.S.H.A. and other regulations dictate that you do not stand on a sawhorse.

Are Bull Brackets engineered for loading ? 
No. We consulted an engineer to conduct such a test and were advised that the wood members would have to be part of the engineering. Since we have no control of the grade or condition of the wood you will use, we cannot provide engineering. Suffice to say the wood should break before the brackets do. Again, common sense should prevail to ensure the brackets and lumber are not overloaded.
 

Can I put screws in to make it stronger ? 
Do not use screws or other fasteners to connect the main Bull Bracket to the legs. You can utilize the screw holes on the spreaders to add a brace to minimize “racking”. You can also add screws to hold the extensions in place when making a table off the side of the sawhorse. Simply drill holes on the top or side of the tube to accept screws. You will also want to use screws to keep plywood tabletops in place.
 

How far can the crossbeams extend before outrigger legs are required ? 
If the extensions go beyond the sawhorse leg footprint, stabilizing legs should be used.
 

Do I have to fasten the spreaders with screws or nails ? 
Definitely! You must ensure the sawhorse won’t shake apart with vibration from power tools, handsaws, hammering, etc. Safety is a big issue when using any type of equipment – be safe!
 

If I use nails to fasten the spreader, how far do I drive them in ? 
Make sure you leave enough of the head showing to remove it with your claw hammer or wrecking bar. If you drive it all the way in, it will be very difficult to remove!
 

When I add my mitre-saw to the two sawhorses to make the work station, can I just drop pins in to hold the plywood deck in place ? 
No! You must use 3/8” bolts with nuts to securely fasten the plywood deck in place! Your mitre-saw is very dangerous if not securely fastened in place.
 

After a few days in the shop, my sawhorse has become loose as the wood dried – how do I fix this ? 
Simply disassemble your sawhorse, reset the spreaders firmly and replace the screws. It only takes a “minute” or so to fix!
 

Can I use pins to secure the spreaders in place ? 
Probably not as you seldom get the spreader in the same location each time due to the moisture content of the wood or the different force you exert each time you assemble your sawhorse.
 

Is there a limit to the length, width or height I can build my Bull Brackets sawhorse ?
There is no limit other than the length of available dimensional lumber. Also it is important to ensure the structure you build with Bull Brackets is safe and stable for the purpose you intend to use it for. Your common sense has to prevail! Do not overload, overbalance, or walk on any structure you build using Bull Brackets.
 

What are some of the alternative uses for Bull Brackets ? 
Our customers have successfully used our brackets in the following ways: Greenhouse (wrapped in clear poly), Saddle Stand (more than one saddle – use a longer 2x6), Tent, Outhouse (wrapped in a tarp), Change Room (wrapped in curtains or tarp), Dog Training Obstacle, Ice Hut (wrapped in a tarp for ice fishing), Paint Booth, Temporary shelter for recreation, work, car or boat, Hunting A-frame to field-dress game, Sawhorse for bucking firewood, and so on. 
 

What if I have a problem using my Bull Brackets ? 
Phone us at (250) 265-3681 or email us . We are here to help!